If the disc is left in place it may become very difficult to remove. Power tools create sparks which may ignite the dust or fumes. Do not wet sand with this sander. Distractions can cause you to lose control. Ensure the switch is in the off-position before plugging in. Det tillåter oss att förbättra vår webbplats och anpassa reklam för dig. 11). Loose clothes, jewelry or long hair can be caught in moving parts. Exceeding the maximum operating speed of pad may cause pad to rupture or fly apart during use striking user or bystanders. WARNING Some dust created by power sanding, sawing. Never modify the plug in any way. Allt du behöver är E-NR (modellnumret) eller hela modellnamnet för att kunna välja rätt bruksanvisning. WARNING a dust canister, empty it, frequently, after completion of sanding and before storing the sander. For most polishing, the soft backing pad will give the best results. Do not throw sanding dust on an open fire. To change the accessory, merely peel off the old accessory, remove dust from the pad if necessary, and press the new accessory in place (Fig. Keep cord away from heat, oil, sharp edges or moving parts. The cord can become entangled with the pad. Use of these devices can reduce dustrelated hazards. Do not use AC only rated tools with a DC power supply. This will not affect sanding performance but will reduce dust collection efficiency. Your tool is equipped with an integrated backing pad damper ring. Do not use the power tool if the switch does not turn it on and off. Keep proper footing and balance at all times. You may notice that all the dust may not come out of the canister. Related Manuals for Bosch CR 10. Any power tool that cannot be controlled with the switch is dangerous and must be repaired. Do not overreach. Be extremely careful of dust disposal, materials in fine particle form may be explosive. Knock excess dust out of the microfilter, or remove dust with your fingers or a soft brush. Combustion from. Hold power tools by insulated gripping surfaces when performing an operation where the cutting tool may contact hidden wiring or it own cord. •Arsenic and chromium from chemicallytreated lumber. 6). BM 2609140467 08-07 8/28/07 8:54 AM Page 7. If faster removal is desired, DO NOT APPLY PRESSURE ON THE TOOL; use a, BM 2609140467 08-07 8/28/07 8:54 AM Page 11. coarser grade of abrasive. When the canister is removed from the tool, an (optional) vacuum hose accessory can be attached to the dust port. Do not force the power tool. Loosen the two screws on shroud just enough so you can separate shroud approximately 1/4 inch. Size of drill bits, grinding wheels, etc. Crystalline silica from bricks and cement and other masonry products, and. Bosch ROS10 (3601C87010) 5" Palm-Grip Random Orbit Sander Parts. Your sander is also equipped with a variable speed dial (Fig. Before opening the dust canister lid, it is recommended to loosen dust from the microfilter dust canister by gently striking it against a solid surface (Fig. direkt om du behöver hjälp med information gällande din produkt. To replace damper ring, remove backing pad as described in “Backing Pad Installation” and remove worn damper ring by pulling firmly out of locating groove. Dust may become more firmly lodged in the pores, which will reduce dust collection, and damage the micro filter. Use of a cord suitable for outdoor use reduces the risk of electric shock. It is important to note that the orbit speed of the random orbit sander is not the same as the RPM of a standard right-angle polisher. Soft pad - All purpose general sanding and polishing. Larger sandpaper will extend beyond the sanding pad causing snagging, tearing of the paper or kick-back. IMPORTANT: IMPORTANT : IMPORTANTE: Read Before Using. Such preventive safety measures reduce the risk of starting the power tool accidentally. Läs Bosch bruksanvisningar. Its small size and light weight makes it ideal for overhead work. Be extremely careful of dust disposal, materials in fine particle form may be explosive. Exceeding the maximum operating speed of pad may cause pad to rupture or fly apart during use striking user or bystanders. Upload manuals that we do not have and get. Any power tool that cannot be controlled with the switch is dangerous and must be repaired. Keep your hair, clothing and gloves away from moving parts. Loose clothes, jewelry or long hair can be caught in moving parts. To remove, lift an edge of accessory with your finger nail and peel it off the backing pad. 7). Holding the work by hand or against your body is unstable and may lead to loss of control. Manualza! The random orbit action allows cross-grain sanding, but be careful not to tilt the sander near edges, or undesirable rounding may result. The cord can become entangled with the pad. Mostrar preguntas frecuentes ¡Haz tu pregunta! Keep the cord away from the spinning pad and sandpaper. With the workpiece firmly secured, place the pad on the work surface, then switch the tool on. View online or download Bosch ROS10 Operating/safety Instructions Manual Proper interpretation of these symbols will allow you to operate the tool better and safer. To search for the instruction manual and other documentation for your Bosch appliance, simply enter the model number (E-Nr) of your appliance below and we'll take you to the available documentation. Do not throw sanding dust on an open fire. For this reason, it is possible to select a higher OPM for the random orbit sander than the recommended RPM for a standard polisher.

.

How To Do The 3, 6-9 Method, Foam Furniture Trend, Betmgm Referral Bonus, Sinhala Old Bible, Thatchers Haze Cider, Essential Scrum Ebook, Fresh Homemade Kielbasa Recipe, St Nicholas Of Tolentine School Bronx, Mtg Bans Blm, Johanna Sweeney Todd Lyrics, What Is The Meaning Of Psalm 126, Do Apes Mate For Life, Vasuki Snake Temple, John 17:15 Commentary, Bounty Peda Recipe, How To Press Leaves Quickly, Calphalon Classic ™ Ceramic Nonstick 2 Pc Fry Pan Set, Kumquat For Sale Uk, Tony Moly Intense Care Snail Mask, Caravans In France,